net: phy: microchip: force IRQ polling mode for lan88xx

[ Upstream commit 30a41ed ]

With lan88xx based devices the lan78xx driver can get stuck in an
interrupt loop while bringing the device up, flooding the kernel log
with messages like the following:

lan78xx 2-3:1.0 enp1s0u3: kevent 4 may have been dropped

Removing interrupt support from the lan88xx PHY driver forces the
driver to use polling instead, which avoids the problem.

The issue has been observed with Raspberry Pi devices at least since
4.14 (see [1], bug report for their downstream kernel), as well as
with Nvidia devices [2] in 2020, where disabling interrupts was the
vendor-suggested workaround (together with the claim that phylib
changes in 4.9 made the interrupt handling in lan78xx incompatible).

Iperf reports well over 900Mbits/sec per direction with client in
--dualtest mode, so there does not seem to be a significant impact on
throughput (lan88xx device connected via switch to the peer).

[1] raspberrypi/linux#2447
[2] https://forums.developer.nvidia.com/t/jetson-xavier-and-lan7800-problem/142134/11

Link: https://lore.kernel.org/[email protected]
Fixes: 792aec4 ("add microchip LAN88xx phy driver")
Signed-off-by: Fiona Klute <[email protected]>
Cc: [email protected]
Cc: [email protected]
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>

Author: airtower-luna

drivers/net/phy/microchip.c

@@ -31,47 +31,6 @@ static int lan88xx_write_page(struct phy_device *phydev, int page)
 	return __phy_write(phydev, LAN88XX_EXT_PAGE_ACCESS, page);
 }
 
-static int lan88xx_phy_config_intr(struct phy_device *phydev)
-{
-	int rc;
-
-	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
-		/* unmask all source and clear them before enable */
-		rc = phy_write(phydev, LAN88XX_INT_MASK, 0x7FFF);
-		rc = phy_read(phydev, LAN88XX_INT_STS);
-		rc = phy_write(phydev, LAN88XX_INT_MASK,
-			       LAN88XX_INT_MASK_MDINTPIN_EN_ |
-			       LAN88XX_INT_MASK_LINK_CHANGE_);
-	} else {
-		rc = phy_write(phydev, LAN88XX_INT_MASK, 0);
-		if (rc)
-			return rc;
-
-		/* Ack interrupts after they have been disabled */
-		rc = phy_read(phydev, LAN88XX_INT_STS);
-	}
-
-	return rc < 0 ? rc : 0;
-}
-
-static irqreturn_t lan88xx_handle_interrupt(struct phy_device *phydev)
-{
-	int irq_status;
-
-	irq_status = phy_read(phydev, LAN88XX_INT_STS);
-	if (irq_status < 0) {
-		phy_error(phydev);
-		return IRQ_NONE;
-	}
-
-	if (!(irq_status & LAN88XX_INT_STS_LINK_CHANGE_))
-		return IRQ_NONE;
-
-	phy_trigger_machine(phydev);
-
-	return IRQ_HANDLED;
-}
-
 static int lan88xx_suspend(struct phy_device *phydev)
 {
 	struct lan88xx_priv *priv = phydev->priv;
@@ -388,8 +347,9 @@ static struct phy_driver microchip_phy_driver[] = {
 	.config_aneg	= lan88xx_config_aneg,
 	.link_change_notify = lan88xx_link_change_notify,
 
-	.config_intr	= lan88xx_phy_config_intr,
-	.handle_interrupt = lan88xx_handle_interrupt,
+	/* Interrupt handling is broken, do not define related
+	 * functions to force polling.
+	 */
 
 	.suspend	= lan88xx_suspend,
 	.resume		= genphy_resume,