Raspberry Pi Zero 2 W Bluetooth audio stutters with WiFi enabled

[cipriantrofin]

Describe the bug

I think there is an interference / Bluetooth and WiFi coexistence problem on Raspberry Pi Zero 2 W.

The isssue is similar with previous reports of this issue on Pi 3.

The issue showed up for me when I tried Moode Audio to stream internet radio or MP3s from my LAN NAS to a Bluetooth speaker. The setup worked fine when using RPi Zero 2 W + USB sound card + speaker but I got sound glitches when I used RPi Zero 2 W + Bluetooth speaker.

To make sure this is not a Moode Audio issue, I tried to reproduce the issue with a simple setup: Raspberry Pi OS 64bit Lite + Pulse Audio + Samba + mpg123. The result was the same: choppy / stuttering sounds when playing MP3s from my NAS and sending the output to an external Bluetooth speaker.

Streaming an MP3 from internal storage to a BT speaker works fine.

Steps to reproduce the behaviour

The setup:

• Raspberry Pi Zero 2 W, official power source, case, 32GB card
• external bluetooth speaker
• NAS hosting MP3s (SAMBA v1)
• local WiFi network

All devices are in same room (proper WiFi coverage).

Steps:

1. fresh Raspberry Pi OS Lite 64bit install (using the official Raspberry Pi Imager)

2. package update
   sudo apt update && sudo apt upgrade -y

3. reboot

4. add pulseaudio package
   sudo apt install pulseaudio-module-bluetooth

5. reboot

6. connect to external BT speaker using bluetoothctl / scan for speaker / connect to speaker

7. install mpg123:
   sudo apt install mpg123

8. mount a Samba share from my NAS and play an MP3 from the share, using mpg123; the audio on BT speaker stutters.

9. copy the same mp3 to Pi's home directory (internal storage): the audio on BT speaker is clean.

Device (s)

Raspberry Pi Zero 2 W

System

Raspberry Pi Zero 2 W Rev 1.0
PRETTY_NAME="Debian GNU/Linux 11 (bullseye)"
NAME="Debian GNU/Linux"
VERSION_ID="11"
VERSION="11 (bullseye)"

Raspberry Pi reference 2022-09-22
Generated using pi-gen, https://github.com/RPi-Distro/pi-gen, 005a8c73b05a2cab39 4073150208bf4f069e861a, stage2

Linux raspberrypi 5.15.76-v8+ #1597 SMP PREEMPT Fri Nov 4 12:16:41 GMT 2022 aarc h64 GNU/Linux
Revision : 902120
Serial : 000000007599bca5
Model : Raspberry Pi Zero 2 W Rev 1.0
Throttled flag : throttled=0x0
Camera : supported=0 detected=0, libcamera interfaces=0

Videocore information

Oct 26 2022 11:10:35
Copyright (c) 2012 Broadcom
version c72ad6b26ff40c91ef776b847436094ee63fabee (clean) (release) (start)

alloc failures: 0
compactions: 0
legacy block fails: 0

Filesystem information

Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 29443572 1795900 26416692 7% /
devtmpfs 81720 0 81720 0% /dev
tmpfs 214712 0 214712 0% /dev/shm
tmpfs 85888 936 84952 2% /run
tmpfs 5120 4 5116 1% /run/lock
/dev/mmcblk0p1 261108 31262 229846 12% /boot
//192.168.76.100/mp3 2882740792 2836916384 45824408 99% /home/pi/nas_mp3
tmpfs 42940 4 42936 1% /run/user/1000

Filename Type Size Used P riority
/var/swap file 102396 0 - 2

Package version information

raspberrypi-ui-mods:
Installed: (none)
raspberrypi-sys-mods:
Installed: 20221019
openbox:
Installed: (none)
lxpanel:
Installed: (none)
pcmanfm:
Installed: (none)
rpd-plym-splash:
Installed: (none)

Networking Information

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet x.x.x.x netmask x.x.x.x
inet6 ::1 prefixlen 128 scopeid 0x10
loop txqueuelen 1000 (Local Loopback)
RX packets 12 bytes 1722 (1.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 12 bytes 1722 (1.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet x.x.x.x netmask x.x.x.x broadcast x.x.x.x
inet6 y::y.y.y.y prefixlen 64 scopeid 0x20
ether m.m.m.m txqueuelen 1000 (Ethernet)
RX packets 106 bytes 10760 (10.5 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 136 bytes 20815 (20.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

USB Information

/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc_otg/1p, 480M

Display Information

Running (F)KMS, console

/sys/class/drm/card0-HDMI-A-1

/sys/class/drm/card0-Writeback-1

kmsprint is not installed. Install with: sudo apt install kms++-utils

/sys/kernel/debug/dri/0/state:
plane[46]: plane-0
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=0
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[57]: plane-1
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=0
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[68]: plane-2
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=0
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[79]: plane-3
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=0
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[90]: plane-4
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=1
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[100]: plane-5
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=2
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[110]: plane-6
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=3
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[120]: plane-7
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=4
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[130]: plane-8
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=5
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[140]: plane-9
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=6
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[150]: plane-10
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=7
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[160]: plane-11
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=8
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[170]: plane-12
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=9
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[180]: plane-13
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=a
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[190]: plane-14
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=b
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[200]: plane-15
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=c
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[210]: plane-16
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=d
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[220]: plane-17
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=e
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[230]: plane-18
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=f
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[240]: plane-19
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=10
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[250]: plane-20
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=11
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[260]: plane-21
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=11
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[270]: plane-22
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=11
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
plane[280]: plane-23
crtc=(null)
fb=0
crtc-pos=0x0+0+0
src-pos=0.000000x0.000000+0.000000+0.000000
rotation=1
normalized-zpos=11
color-encoding=ITU-R BT.709 YCbCr
color-range=YCbCr limited range
crtc[56]: crtc-0
enable=0
active=0
self_refresh_active=0
planes_changed=0
mode_changed=0
active_changed=0
connectors_changed=0
color_mgmt_changed=0
plane_mask=0
connector_mask=0
encoder_mask=0
mode: "": 0 0 0 0 0 0 0 0 0 0 0x0 0x0
crtc[67]: crtc-1
enable=0
active=0
self_refresh_active=0
planes_changed=0
mode_changed=0
active_changed=0
connectors_changed=0
color_mgmt_changed=0
plane_mask=0
connector_mask=0
encoder_mask=0
mode: "": 0 0 0 0 0 0 0 0 0 0 0x0 0x0
crtc[78]: crtc-2
enable=0
active=0
self_refresh_active=0
planes_changed=0
mode_changed=0
active_changed=0
connectors_changed=0
color_mgmt_changed=0
plane_mask=0
connector_mask=0
encoder_mask=0
mode: "": 0 0 0 0 0 0 0 0 0 0 0x0 0x0
crtc[89]: crtc-3
enable=0
active=0
self_refresh_active=0
planes_changed=0
mode_changed=0
active_changed=0
connectors_changed=0
color_mgmt_changed=0
plane_mask=0
connector_mask=0
encoder_mask=0
mode: "": 0 0 0 0 0 0 0 0 0 0 0x0 0x0
connector[32]: HDMI-A-1
crtc=(null)
self_refresh_aware=0
connector[45]: Writeback-1
crtc=(null)
self_refresh_aware=0

config.txt

aphy_params_current=819
arm_64bit=1
arm_freq=1000
arm_freq_min=600
audio_pwm_mode=514
camera_auto_detect=1
config_hdmi_boost=5
core_freq=400
desired_osc_freq=0x331df0
disable_commandline_tags=2
disable_l2cache=1
disable_overscan=1
display_auto_detect=1
display_hdmi_rotate=-1
display_lcd_rotate=-1
dphy_params_current=547
dvfs=3
enable_tvout=1
force_eeprom_read=1
force_pwm_open=1
framebuffer_ignore_alpha=1
framebuffer_swap=1
gpu_freq=300
ignore_lcd=1
init_uart_clock=0x2dc6c00
mask_gpu_interrupt0=3072
mask_gpu_interrupt1=26370
max_framebuffers=2
over_voltage_avs=12500
pause_burst_frames=1
program_serial_random=1
sdram_freq=450
total_mem=512
hdmi_force_cec_address:0=65535
hdmi_force_cec_address:1=65535
hdmi_pixel_freq_limit:0=0x9a7ec80
device_tree=-
overlay_prefix=overlays/
hdmi_cvt:0=
hdmi_cvt:1=
hdmi_edid_filename:0=
hdmi_edid_filename:1=
hdmi_timings:0=
hdmi_timings:1=

cmdline.txt

coherent_pool=1M 8250.nr_uarts=0 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 video=Composite-1:720x480@60i smsc95xx.macaddr=B8:27:EB:99:BC:A5 vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000 console=ttyS0,115200 console=tty1 root=PARTUUID=1e4838ea-02 rootfstype=ext4 fsck.repair=yes rootwait

raspi-gpio settings

BANK0 (GPIO 0 to 27):
GPIO 0: level=1 fsel=0 func=INPUT
GPIO 1: level=1 fsel=0 func=INPUT
GPIO 2: level=1 fsel=0 func=INPUT
GPIO 3: level=1 fsel=0 func=INPUT
GPIO 4: level=1 fsel=0 func=INPUT
GPIO 5: level=1 fsel=0 func=INPUT
GPIO 6: level=1 fsel=0 func=INPUT
GPIO 7: level=1 fsel=0 func=INPUT
GPIO 8: level=1 fsel=0 func=INPUT
GPIO 9: level=0 fsel=0 func=INPUT
GPIO 10: level=0 fsel=0 func=INPUT
GPIO 11: level=0 fsel=0 func=INPUT
GPIO 12: level=0 fsel=0 func=INPUT
GPIO 13: level=0 fsel=0 func=INPUT
GPIO 14: level=0 fsel=0 func=INPUT
GPIO 15: level=1 fsel=0 func=INPUT
GPIO 16: level=0 fsel=0 func=INPUT
GPIO 17: level=0 fsel=0 func=INPUT
GPIO 18: level=0 fsel=0 func=INPUT
GPIO 19: level=0 fsel=0 func=INPUT
GPIO 20: level=0 fsel=0 func=INPUT
GPIO 21: level=0 fsel=0 func=INPUT
GPIO 22: level=0 fsel=0 func=INPUT
GPIO 23: level=0 fsel=0 func=INPUT
GPIO 24: level=0 fsel=0 func=INPUT
GPIO 25: level=0 fsel=0 func=INPUT
GPIO 26: level=0 fsel=0 func=INPUT
GPIO 27: level=0 fsel=0 func=INPUT
BANK1 (GPIO 28 to 45):
GPIO 28: level=1 fsel=0 func=INPUT
GPIO 29: level=0 fsel=1 func=OUTPUT
GPIO 30: level=0 fsel=7 alt=3 func=CTS0
GPIO 31: level=0 fsel=7 alt=3 func=RTS0
GPIO 32: level=1 fsel=7 alt=3 func=TXD0
GPIO 33: level=1 fsel=7 alt=3 func=RXD0
GPIO 34: level=0 fsel=7 alt=3 func=SD1_CLK
GPIO 35: level=1 fsel=7 alt=3 func=SD1_CMD
GPIO 36: level=1 fsel=7 alt=3 func=SD1_DAT0
GPIO 37: level=1 fsel=7 alt=3 func=SD1_DAT1
GPIO 38: level=1 fsel=7 alt=3 func=SD1_DAT2
GPIO 39: level=1 fsel=7 alt=3 func=SD1_DAT3
GPIO 40: level=0 fsel=1 func=OUTPUT
GPIO 41: level=1 fsel=1 func=OUTPUT
GPIO 42: level=1 fsel=1 func=OUTPUT
GPIO 43: level=1 fsel=4 alt=0 func=GPCLK2
GPIO 44: level=1 fsel=0 func=INPUT
GPIO 45: level=1 fsel=0 func=INPUT
BANK2 (GPIO 46 to 53):
GPIO 46: level=1 fsel=0 func=INPUT
GPIO 47: level=1 fsel=1 func=OUTPUT
GPIO 48: level=0 fsel=4 alt=0 func=SD0_CLK
GPIO 49: level=1 fsel=4 alt=0 func=SD0_CMD
GPIO 50: level=1 fsel=4 alt=0 func=SD0_DAT0
GPIO 51: level=1 fsel=4 alt=0 func=SD0_DAT1
GPIO 52: level=1 fsel=4 alt=0 func=SD0_DAT2
GPIO 53: level=1 fsel=4 alt=0 func=SD0_DAT3

vcdbg log messages

sudo: vcdbg: command not found

dmesg log

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.76-v8+ (dom@buildbot) (aarch64-linux-gnu-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1597 SMP PREEMPT Fri Nov 4 12:16:41 GMT 2022
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Raspberry Pi Zero 2 W Rev 1.0
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000000bc00000, size 256 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000001bffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000001bffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001bffffff]
[ 0.000000] On node 0, zone DMA: 16384 pages in unavailable ranges
[ 0.000000] percpu: Embedded 28 pages/cpu s77336 r8192 d29160 u114688
[ 0.000000] pcpu-alloc: s77336 r8192 d29160 u114688 alloc=28*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: kernel page table isolation forced ON by KASLR
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] CPU features: detected: ARM erratum 843419
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 112896
[ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 video=Composite-1:720x480@60i smsc95xx.macaddr=m.m.m.m vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000 console=ttyS0,115200 console=tty1 root=PARTUUID=1e4838ea-02 rootfstype=ext4 fsck.repair=yes rootwait
[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 163444K/458752K available (11520K kernel code, 1956K rwdata, 4148K rodata, 3840K init, 975K bss, 33164K reserved, 262144K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 38059 entries in 149 pages
[ 0.000000] ftrace: allocated 149 pages with 4 groups
[ 0.000000] trace event string verifier disabled
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: bcm2836_arm_irqchip_handle_irq
[ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000392] Console: colour dummy device 80x25
[ 0.001330] printk: console [tty1] enabled
[ 0.001414] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[ 0.001479] pid_max: default: 32768 minimum: 301
[ 0.001684] LSM: Security Framework initializing
[ 0.001960] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.002021] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.003736] cgroup: Disabling memory control group subsystem
[ 0.007838] rcu: Hierarchical SRCU implementation.
[ 0.009340] EFI services will not be available.
[ 0.010115] smp: Bringing up secondary CPUs ...
[ 0.011689] Detected VIPT I-cache on CPU1
[ 0.011785] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.013512] Detected VIPT I-cache on CPU2
[ 0.013580] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.015236] Detected VIPT I-cache on CPU3
[ 0.015293] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.015505] smp: Brought up 1 node, 4 CPUs
[ 0.015662] SMP: Total of 4 processors activated.
[ 0.015696] CPU features: detected: 32-bit EL0 Support
[ 0.015729] CPU features: detected: 32-bit EL1 Support
[ 0.015764] CPU features: detected: CRC32 instructions
[ 0.056145] CPU: All CPU(s) started at EL2
[ 0.056294] alternatives: patching kernel code
[ 0.058240] devtmpfs: initialized
[ 0.080138] Enabled cp15_barrier support
[ 0.080223] Enabled setend support
[ 0.080305] KASLR enabled
[ 0.080604] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.080675] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.093310] pinctrl core: initialized pinctrl subsystem
[ 0.094536] DMI not present or invalid.
[ 0.095548] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.106657] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 0.107170] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.108656] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.108850] audit: initializing netlink subsys (disabled)
[ 0.109296] audit: type=2000 audit(0.108:1): state=initialized audit_enabled=0 res=1
[ 0.110196] thermal_sys: Registered thermal governor 'step_wise'
[ 0.110565] cpuidle: using governor menu
[ 0.111156] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.111468] ASID allocator initialised with 32768 entries
[ 0.111731] Serial: AMBA PL011 UART driver
[ 0.126285] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[ 0.156769] raspberrypi-firmware soc:firmware: Attached to firmware from 2022-10-26T11:10:35, variant start
[ 0.160787] raspberrypi-firmware soc:firmware: Firmware hash is c72ad6b26ff40c91ef776b847436094ee63fabee
[ 0.220575] bcm2835-dma 3f007000.dma: DMA legacy API manager, dmachans=0x1
[ 0.226181] vgaarb: loaded
[ 0.226881] SCSI subsystem initialized
[ 0.227220] usbcore: registered new interface driver usbfs
[ 0.227335] usbcore: registered new interface driver hub
[ 0.227454] usbcore: registered new device driver usb
[ 0.227995] usb_phy_generic phy: supply vcc not found, using dummy regulator
[ 0.228349] usb_phy_generic phy: dummy supplies not allowed for exclusive requests
[ 0.228764] pps_core: LinuxPPS API ver. 1 registered
[ 0.228801] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [email protected]
[ 0.228865] PTP clock support registered
[ 0.231164] clocksource: Switched to clocksource arch_sys_counter
[ 0.355953] VFS: Disk quotas dquot_6.6.0
[ 0.356136] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.356407] FS-Cache: Loaded
[ 0.356745] CacheFiles: Loaded
[ 0.358118] simple-framebuffer 1eaa9000.framebuffer: framebuffer at 0x1eaa9000, 0x151800 bytes
[ 0.358172] simple-framebuffer 1eaa9000.framebuffer: format=a8r8g8b8, mode=720x480x32, linelength=2880
[ 0.364614] Console: switching to colour frame buffer device 90x30
[ 0.373103] simple-framebuffer 1eaa9000.framebuffer: fb0: simplefb registered!
[ 0.391552] NET: Registered PF_INET protocol family
[ 0.394940] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.399876] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.406426] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.409987] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.413673] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.417382] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.421227] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.424923] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.429459] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.434377] RPC: Registered named UNIX socket transport module.
[ 0.437988] RPC: Registered udp transport module.
[ 0.441590] RPC: Registered tcp transport module.
[ 0.445015] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.448456] PCI: CLS 0 bytes, default 64
[ 0.454216] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 0.461543] kvm [1]: IPA Size Limit: 40 bits
[ 0.466749] kvm [1]: Hyp mode initialized successfully
[ 1.739225] Initialise system trusted keyrings
[ 1.743092] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[ 1.757062] zbud: loaded
[ 1.763122] FS-Cache: Netfs 'nfs' registered for caching
[ 1.767419] NFS: Registering the id_resolver key type
[ 1.770648] Key type id_resolver registered
[ 1.773791] Key type id_legacy registered
[ 1.776963] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.780013] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.784867] Key type asymmetric registered
[ 1.787867] Asymmetric key parser 'x509' registered
[ 1.790877] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.794342] io scheduler mq-deadline registered
[ 1.797304] io scheduler kyber registered
[ 1.815579] bcm2835-rng 3f104000.rng: hwrng registered
[ 1.819424] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000000(512 MiB)
[ 1.827333] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 1.849519] brd: module loaded
[ 1.867667] loop: module loaded
[ 1.871845] Loading iSCSI transport class v2.0-870.
[ 1.881772] usbcore: registered new interface driver r8152
[ 1.884931] usbcore: registered new interface driver lan78xx
[ 1.887973] usbcore: registered new interface driver smsc95xx
[ 1.891560] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 2.623093] Core Release: 2.80a
[ 2.625965] Setting default values for core params
[ 2.628834] Finished setting default values for core params
[ 2.832224] Using Buffer DMA mode
[ 2.835033] Periodic Transfer Interrupt Enhancement - disabled
[ 2.837939] Multiprocessor Interrupt Enhancement - disabled
[ 2.840909] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 2.843822] Dedicated Tx FIFOs mode

[ 2.851239] WARN::dwc_otg_hcd_init:1074: FIQ DMA bounce buffers: virt = ffffffc008471000 dma = 0x00000000cc000000 len=9024
[ 2.859620] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[ 2.873162] dwc_otg: Microframe scheduler enabled

[ 2.873238] WARN::hcd_init_fiq:497: MPHI regs_base at ffffffc008065000
[ 2.878358] dwc_otg 3f980000.usb: DWC OTG Controller
[ 2.881010] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[ 2.883751] dwc_otg 3f980000.usb: irq 74, io mem 0x00000000
[ 2.886414] Init: Port Power? op_state=1
[ 2.889089] Init: Power Port (0)
[ 2.892320] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[ 2.897868] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.900846] usb usb1: Product: DWC OTG Controller
[ 2.903777] usb usb1: Manufacturer: Linux 5.15.76-v8+ dwc_otg_hcd
[ 2.906715] usb usb1: SerialNumber: 3f980000.usb
[ 2.910650] hub 1-0:1.0: USB hub found
[ 2.913600] hub 1-0:1.0: 1 port detected
[ 2.917637] dwc_otg: FIQ enabled
[ 2.917656] dwc_otg: NAK holdoff enabled
[ 2.917671] dwc_otg: FIQ split-transaction FSM enabled
[ 2.917692] Module dwc_common_port init
[ 2.918454] usbcore: registered new interface driver uas
[ 2.921441] usbcore: registered new interface driver usb-storage
[ 2.924809] mousedev: PS/2 mouse device common for all mice
[ 2.932720] sdhci: Secure Digital Host Controller Interface driver
[ 2.935502] sdhci: Copyright(c) Pierre Ossman
[ 2.938969] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.944420] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.948074] hid: raw HID events driver (C) Jiri Kosina
[ 2.951115] usbcore: registered new interface driver usbhid
[ 2.953994] usbhid: USB HID core driver
[ 2.957252] ashmem: initialized
[ 2.968393] NET: Registered PF_PACKET protocol family
[ 2.971402] Key type dns_resolver registered
[ 2.976000] registered taskstats version 1
[ 2.978727] Loading compiled-in X.509 certificates
[ 2.982398] Key type ._fscrypt registered
[ 2.985155] Key type .fscrypt registered
[ 2.987788] Key type fscrypt-provisioning registered
[ 3.009781] uart-pl011 3f201000.serial: cts_event_workaround enabled
[ 3.012569] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 99, base_baud = 0) is a PL011 rev2
[ 3.022583] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 3.025984] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[ 3.031572] mmc-bcm2835 3f300000.mmcnr: mmc_debug:0 mmc_debug2:0
[ 3.034403] mmc-bcm2835 3f300000.mmcnr: DMA channel allocated
[ 3.064339] sdhost: log_buf @ 000000006af75cbc (c2ee3000)
[ 3.131236] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 3.138806] of_cfs_init
[ 3.141794] of_cfs_init: OK
[ 3.146077] Waiting for root device PARTUUID=1e4838ea-02...
[ 3.178924] mmc0: host does not support reading read-only switch, assuming write-enable
[ 3.183691] mmc0: Problem switching card into high-speed mode!
[ 3.187894] mmc0: new SDHC card at address 0001
[ 3.192603] mmcblk0: mmc0:0001 SD32G 28.8 GiB
[ 3.201279] mmcblk0: p1 p2
[ 3.205085] mmcblk0: mmc0:0001 SD32G 28.8 GiB
[ 3.237467] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[ 3.243454] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 3.248738] mmc1: new high speed SDIO card at address 0001
[ 3.262075] devtmpfs: mounted
[ 3.275881] Freeing unused kernel memory: 3840K
[ 3.279226] Run /sbin/init as init process
[ 3.282283] with arguments:
[ 3.282297] /sbin/init
[ 3.282312] with environment:
[ 3.282325] HOME=/
[ 3.282339] TERM=linux
[ 4.316549] systemd[1]: System time before build time, advancing clock.
[ 4.655787] NET: Registered PF_INET6 protocol family
[ 4.661250] Segment Routing with IPv6
[ 4.664317] In-situ OAM (IOAM) with IPv6
[ 4.779381] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 4.790202] systemd[1]: Detected architecture arm64.
[ 4.847565] systemd[1]: Set hostname to .
[ 6.073667] systemd[1]: Queued start job for default target Multi-User System.
[ 6.084037] systemd[1]: Created slice system-getty.slice.
[ 6.093156] systemd[1]: Created slice system-modprobe.slice.
[ 6.102075] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 6.110776] systemd[1]: Created slice User and Session Slice.
[ 6.118642] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 6.126737] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 6.136129] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 6.148107] systemd[1]: Reached target Local Encrypted Volumes.
[ 6.156528] systemd[1]: Reached target Paths.
[ 6.164377] systemd[1]: Reached target Slices.
[ 6.172130] systemd[1]: Reached target Swap.
[ 6.181111] systemd[1]: Listening on Syslog Socket.
[ 6.189930] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 6.198384] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 6.208194] systemd[1]: Listening on Journal Audit Socket.
[ 6.217226] systemd[1]: Listening on Journal Socket (/dev/log).
[ 6.226485] systemd[1]: Listening on Journal Socket.
[ 6.237330] systemd[1]: Listening on udev Control Socket.
[ 6.246026] systemd[1]: Listening on udev Kernel Socket.
[ 6.254592] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 6.267032] systemd[1]: Mounting POSIX Message Queue File System...
[ 6.281329] systemd[1]: Mounting RPC Pipe File System...
[ 6.296085] systemd[1]: Mounting Kernel Debug File System...
[ 6.311209] systemd[1]: Mounting Kernel Trace File System...
[ 6.319836] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[ 6.336545] systemd[1]: Starting Restore / save the current clock...
[ 6.360711] systemd[1]: Starting Set the console keyboard layout...
[ 6.377098] systemd[1]: Starting Create list of static device nodes for the current kernel...
[ 6.397339] systemd[1]: Starting Load Kernel Module configfs...
[ 6.414145] systemd[1]: Starting Load Kernel Module drm...
[ 6.430040] systemd[1]: Starting Load Kernel Module fuse...
[ 6.465628] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 6.479827] systemd[1]: Starting File System Check on Root Device...
[ 6.503772] systemd[1]: Starting Journal Service...
[ 6.542862] fuse: init (API version 7.34)
[ 6.549402] systemd[1]: Starting Load Kernel Modules...
[ 6.580463] systemd[1]: Starting Coldplug All udev Devices...
[ 6.624304] systemd[1]: Mounted POSIX Message Queue File System.
[ 6.634366] systemd[1]: Mounted RPC Pipe File System.
[ 6.643697] systemd[1]: Mounted Kernel Debug File System.
[ 6.653482] systemd[1]: Mounted Kernel Trace File System.
[ 6.664493] systemd[1]: Finished Restore / save the current clock.
[ 6.678332] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ 6.696612] systemd[1]: [email protected]: Succeeded.
[ 6.703271] systemd[1]: Finished Load Kernel Module configfs.
[ 6.714069] systemd[1]: [email protected]: Succeeded.
[ 6.720652] systemd[1]: Finished Load Kernel Module drm.
[ 6.731621] systemd[1]: [email protected]: Succeeded.
[ 6.737517] systemd[1]: Finished Load Kernel Module fuse.
[ 6.749530] systemd[1]: Finished Load Kernel Modules.
[ 6.768518] systemd[1]: Mounting FUSE Control File System...
[ 6.785408] systemd[1]: Mounting Kernel Configuration File System...
[ 6.801021] systemd[1]: Started File System Check Daemon to report status.
[ 6.821627] systemd[1]: Starting Apply Kernel Variables...
[ 6.838583] systemd[1]: Mounted FUSE Control File System.
[ 6.847426] systemd[1]: Mounted Kernel Configuration File System.
[ 6.910857] systemd[1]: Started Journal Service.
[ 7.301406] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null). Quota mode: none.
[ 7.394047] systemd-journald[137]: Received client request to flush runtime journal.
[ 7.439372] systemd-journald[137]: File /var/log/journal/9ede25a8ac58409783cbe8ef9ef4a6eb/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 9.156807] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[ 9.165061] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[ 9.165123] [vc_sm_connected_init]: start
[ 9.166348] [vc_sm_connected_init]: installed successfully
[ 9.224902] mc: Linux media interface: v0.10
[ 9.379768] videodev: Linux video capture interface: v2.00
[ 9.404023] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 9.406873] bcm2835_audio bcm2835_audio: there is not valid maps for state default
[ 9.460702] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 9.464889] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 9.488579] bcm2835_isp: module is from the staging directory, the quality is unknown, you have been warned.
[ 9.497651] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video13
[ 9.498295] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video14
[ 9.498801] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video15
[ 9.499303] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video16
[ 9.499355] bcm2835-isp bcm2835-isp: Register output node 0 with media controller
[ 9.499407] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller
[ 9.499437] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller
[ 9.499464] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller
[ 9.508271] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video20
[ 9.509049] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video21
[ 9.509591] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video22
[ 9.510035] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video23
[ 9.510080] bcm2835-isp bcm2835-isp: Register output node 0 with media controller
[ 9.510114] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller
[ 9.510143] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller
[ 9.510170] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller
[ 9.510462] bcm2835-isp bcm2835-isp: Loaded V4L2 bcm2835-isp
[ 9.518547] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[ 9.526834] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[ 9.551693] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[ 9.551781] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[ 9.559695] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[ 9.559774] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[ 9.564250] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[ 9.564352] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[ 9.567748] bcm2835-codec bcm2835-codec: Device registered as /dev/video18
[ 9.567827] bcm2835-codec bcm2835-codec: Loaded V4L2 image_fx
[ 9.572273] bcm2835-codec bcm2835-codec: Device registered as /dev/video31
[ 9.572350] bcm2835-codec bcm2835-codec: Loaded V4L2 encode_image
[ 9.789396] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 9.828874] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 9.845356] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid
[ 10.051889] brcmfmac: F1 signature read @0x18000000=0x1541a9a6
[ 10.082223] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43436s-sdio for chip BCM43430/1
[ 10.084876] usbcore: registered new interface driver brcmfmac
[ 10.437502] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43436s-sdio for chip BCM43430/1
[ 10.439333] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43436s-sdio for chip BCM43430/1
[ 10.439534] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 10.440665] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43430/1 wl0: Jul 5 2022 21:29:56 version 7.45.96.141 (g53ba0094) FWID 01-eef9b3bf es7
[ 10.772279] checking generic (1eaa9000 151800) vs hw (0 ffffffffffffffff)
[ 10.772324] fb0: switching to vc4 from simple
[ 10.773055] Console: switching to colour dummy device 80x25
[ 10.777558] vc4-drm soc:gpu: bound 3f400000.hvs (ops vc4_hvs_ops [vc4])
[ 10.804941] Registered IR keymap rc-cec
[ 10.805262] rc rc0: vc4 as /devices/platform/soc/3f902000.hdmi/rc/rc0
[ 10.805681] input: vc4 as /devices/platform/soc/3f902000.hdmi/rc/rc0/input0
[ 10.862513] vc4-drm soc:gpu: bound 3f902000.hdmi (ops vc4_hdmi_ops [vc4])
[ 10.866203] vc4-drm soc:gpu: bound 3f004000.txp (ops vc4_txp_ops [vc4])
[ 10.866864] vc4-drm soc:gpu: bound 3f206000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 10.878219] vc4-drm soc:gpu: bound 3f207000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 10.879509] vc4-drm soc:gpu: bound 3f807000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 10.879941] vc4-drm soc:gpu: bound 3fc00000.v3d (ops vc4_v3d_ops [vc4])
[ 10.902989] [drm] Initialized vc4 0.0.0 20140616 for soc:gpu on minor 0
[ 10.904470] vc4-drm soc:gpu: [drm] Cannot find any crtc or sizes
[ 12.216329] uart-pl011 3f201000.serial: no DMA platform data
[ 12.430375] 8021q: 802.1Q VLAN Support v1.8
[ 12.622376] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS
[ 13.090738] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 14.681955] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 19.163126] Bluetooth: Core ver 2.22
[ 19.163396] NET: Registered PF_BLUETOOTH protocol family
[ 19.163416] Bluetooth: HCI device and connection manager initialized
[ 19.163462] Bluetooth: HCI socket layer initialized
[ 19.163489] Bluetooth: L2CAP socket layer initialized
[ 19.163539] Bluetooth: SCO socket layer initialized
[ 19.188525] Bluetooth: HCI UART driver ver 2.3
[ 19.188573] Bluetooth: HCI UART protocol H4 registered
[ 19.188748] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 19.189222] Bluetooth: HCI UART protocol Broadcom registered
[ 20.244323] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 20.244366] Bluetooth: BNEP filters: protocol multicast
[ 20.244409] Bluetooth: BNEP socket layer initialized
[ 20.288452] NET: Registered PF_ALG protocol family
[ 20.959808] vc4-drm soc:gpu: [drm] Cannot find any crtc or sizes
[ 21.023763] FS-Cache: Netfs 'cifs' registered for caching
[ 21.044568] Key type cifs.spnego registered
[ 21.044624] Key type cifs.idmap registered
[ 21.049277] Use of the less secure dialect vers=1.0 is not recommended unless required for access to very old servers

[ 21.049321] CIFS: VFS: Use of the less secure dialect vers=1.0 is not recommended unless required for access to very old servers
[ 21.049351] CIFS: Attempting to mount \192.168.76.100\mp3
[ 33.759317] cam-dummy-reg: disabling
[ 35.926153] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 35.926208] MAI: soc_pcm_open() failed (-19)
[ 35.927706] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 35.927751] MAI: soc_pcm_open() failed (-19)
[ 35.929111] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 35.929155] MAI: soc_pcm_open() failed (-19)
[ 35.945160] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 35.945318] MAI: soc_pcm_open() failed (-19)
[ 35.945966] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 35.946080] MAI: soc_pcm_open() failed (-19)
[ 35.946705] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 35.946820] MAI: soc_pcm_open() failed (-19)
[ 36.370973] Bluetooth: RFCOMM TTY layer initialized
[ 36.371031] Bluetooth: RFCOMM socket layer initialized
[ 36.371072] Bluetooth: RFCOMM ver 1.11

Logs

No response

Additional context

No response

[pelwell]

Duplicate of RPi-Distro/firmware-nonfree#33.