LPC4337 stdio fixes for lpcxpresso board

libraries/mbed/targets/hal/TARGET_NXP/TARGET_LPC43XX/PeripheralNames.h → libraries/mbed/targets/hal/TARGET_NXP/TARGET_LPC43XX/TARGET_LPC4330/PeripheralNames.h

@@ -89,6 +89,7 @@ typedef enum {
 #define STDIO_UART_TX     USBTX
 #define STDIO_UART_RX     USBRX
 #define STDIO_UART        UART_2
+#define STDIO_BAUD        115200
 
 // Default peripherals
 #define MBED_SPI0         SPI0_MOSI, SPI0_MISO, SPI0_SCK, SPI0_SSEL

libraries/mbed/targets/hal/TARGET_NXP/TARGET_LPC43XX/TARGET_LPC4337/PeripheralNames.h

@@ -0,0 +1,136 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2013 ARM Limited
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+#ifndef MBED_PERIPHERALNAMES_H
+#define MBED_PERIPHERALNAMES_H
+
+#include "cmsis.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+typedef enum {
+    UART_0 = (int)LPC_USART0_BASE,
+    UART_1 = (int)LPC_UART1_BASE,
+    UART_2 = (int)LPC_USART2_BASE,
+    UART_3 = (int)LPC_USART3_BASE
+} UARTName;
+
+typedef enum {
+    ADC0_0 = 0,
+    ADC0_1,
+    ADC0_2,
+    ADC0_3,
+    ADC0_4,
+    ADC0_5,
+    ADC0_6,
+    ADC0_7,
+    ADC1_0,
+    ADC1_1,
+    ADC1_2,
+    ADC1_3,
+    ADC1_4,
+    ADC1_5,
+    ADC1_6,
+    ADC1_7
+} ADCName;
+
+typedef enum {
+    DAC_0 = 0
+} DACName;
+
+typedef enum {
+    SPI_0 = (int)LPC_SSP0_BASE,
+    SPI_1 = (int)LPC_SSP1_BASE
+} SPIName;
+
+typedef enum {
+    I2C_0 = (int)LPC_I2C0_BASE,
+    I2C_1 = (int)LPC_I2C1_BASE
+} I2CName;
+
+typedef enum {
+    PWM_0,
+    PWM_1,
+    PWM_2,
+    PWM_3,
+    PWM_4,
+    PWM_5,
+    PWM_6,
+    PWM_7,
+    PWM_8,
+    PWM_9,
+    PWM_10,
+    PWM_11,
+    PWM_12,
+    PWM_13,
+    PWM_14,
+    PWM_15
+} PWMName;
+
+typedef enum {
+     CAN_0 = (int)LPC_C_CAN0_BASE,
+     CAN_1 = (int)LPC_C_CAN1_BASE
+} CANName;
+
+#define STDIO_UART_TX     USBTX
+#define STDIO_UART_RX     USBRX
+#define STDIO_UART        UART_0
+#define STDIO_BAUD        9600
+
+// Default peripherals
+#define MBED_SPI0         SPI0_MOSI, SPI0_MISO, SPI0_SCK, SPI0_SSEL
+#define MBED_SPI1         SPI1_MOSI, SPI1_MISO, SPI1_SCK, SPI1_SSEL
+
+#define MBED_UART0        UART0_TX, UART0_RX
+#define MBED_UART1        UART1_TX, UART1_RX
+#define MBED_UART2        UART2_TX, UART2_RX
+#define MBED_UART3        UART3_TX, UART3_RX
+#define MBED_UARTUSB      USBTX, USBRX
+
+#define COM1              MBED_UART0
+#define COM2              MBED_UART1
+#define COM3              MBED_UART2
+#define COM4              MBED_UART3
+
+#define MBED_I2C0         I2C0_SDA, I2C0_SCL
+#define MBED_I2C1         I2C1_SDA, I2C1_SCL
+
+#define MBED_CAN0         p30, p29
+
+#define MBED_ANALOGOUT0   DAC0
+
+#define MBED_ANALOGIN0    ADC0
+#define MBED_ANALOGIN1    ADC1
+#define MBED_ANALOGIN2    ADC2
+#define MBED_ANALOGIN3    ADC3
+#define MBED_ANALOGIN4    ADC4
+#define MBED_ANALOGIN5    ADC5
+#define MBED_ANALOGIN6    ADC6
+#define MBED_ANALOGIN7    ADC7
+
+#define MBED_PWMOUT0      p26
+#define MBED_PWMOUT1      p25
+#define MBED_PWMOUT2      p24
+#define MBED_PWMOUT3      p23
+#define MBED_PWMOUT4      p22
+#define MBED_PWMOUT5      p21
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif

libraries/mbed/targets/hal/TARGET_NXP/TARGET_LPC43XX/serial_api.c

@@ -134,8 +134,7 @@ void serial_init(serial_t *obj, PinName tx, PinName rx) {
                    | 0 << 2; // Rx Line Status irq enable
 
     // set default baud rate and format
-    is_stdio_uart = (uart == STDIO_UART) ? (1) : (0);   
-    serial_baud  (obj, is_stdio_uart ? 115200 : 9600);
+    serial_baud (obj, 9600);
     serial_format(obj, 8, ParityNone, 1);
 
     // pinout the chosen uart
@@ -160,8 +159,11 @@ void serial_init(serial_t *obj, PinName tx, PinName rx) {
     uart_data[obj->index].sw_cts.pin = NC;
     serial_set_flow_control(obj, FlowControlNone, NC, NC);
 
+    is_stdio_uart = (uart == STDIO_UART) ? (1) : (0);
+
     if (is_stdio_uart) {
         stdio_uart_inited = 1;
+        serial_baud (obj, STDIO_BAUD);
         memcpy(&stdio_uart, obj, sizeof(serial_t));
     }
 }