Open
Description
I've tried to compile and flash the current release on my multigeiger (which I build on one of the workshops a couple of years ago) but run into the "multiple definition of `hal_init'" problem (#461). After usi8ng the current HEAD of the codebase, the problem was gone, but after a successful flash of the firmware, the device constantly crashes and reboots with the following output:
Rebooting...
ets Jun 8 2016 00:22:57
rst:0xc (SW_CPU_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13192
load:0x40080400,len:3028
entry 0x400805e4
GEIGER: 1970-01-01T00:00:06 Logging initialized at level 1.
GEIGER: 1970-01-01T00:00:06 BME_Status: not found
Config version: 015
Config size: 243
Wrong config version. Applying defaults.
[iwcAll]
|-- [iwcSys]
| |-- 'iwcThingName' with value: 'ESP32-11869500'
| |-- 'iwcApPassword' with value: <hidden>
| |-- [iwcWifi0]
| | |-- 'iwcWifiSsid' with value: ''
| | \-- 'iwcWifiPassword' with value: <hidden>
| \-- 'iwcApTimeout' with value: '30'
|-- [iwcCustom]
| |-- [misc]
| | |-- 'startSound' with value: 'selected'
| | |-- 'speakerTick' with value: ''
| | |-- 'ledTick' with value: 'selected'
| | \-- 'showDisplay' with value: 'selected'
| |-- [transmission]
| | |-- 'send2Community' with value: 'selected'
| | |-- 'send2Madavi' with value: 'selected'
| | \-- 'send2ble' with value: ''
| \-- [alarm]
| |-- 'soundLocalAlarm' with value: ''
| |-- 'localAlarmThreshold' with value: '0.50'
| \-- 'localAlarmFactor' with value: '3'
\-- [hidden]
GEIGER: 1970-01-01T00:00:06 ------------------------------------------------------------------------------------------------------------------------
GEIGER: 1970-01-01T00:00:06 Simple Multi-Geiger, Version V1.17.0-dev
GEIGER: 1970-01-01T00:00:06 ------------------------------------------------------------------------------------------------------------------------
[ 840][E][esp32-hal-gpio.c:102] __pinMode(): Invalid pin selected
E (815) gpio: gpio_set_level(226): GPIO output gpio_num error
AP password was not set in configuration
State changing from: 0 to 1
Setting up AP: ESP32-11869500
With default password: <hidden>
AP IP address: 192.168.4.1
AP password was not set.
WiFi SSID was not set.
Will stay in AP mode.
State changed from: 0 to 1
Guru Meditation Error: Core 1 panic'ed (LoadProhibited). Exception was unhandled.
Core 1 register dump:
PC : 0x40085884 PS : 0x00050031 A0 : 0x8008167e A1 : 0x3ffc0f4c
A2 : 0x00002000 A3 : 0x0001a000 A4 : 0x000637ff A5 : 0x3ffc0f2c
A6 : 0x00000008 A7 : 0x3ffbf5a4 A8 : 0x00000000 A9 : 0x00000000
A10 : 0x000003e8 A11 : 0x003fffff A12 : 0x80082261 A13 : 0x3ffc0f0c
A14 : 0x3ffc9998 A15 : 0xfffffbff SAR : 0x00000004 EXCCAUSE: 0x0000001c
EXCVADDR: 0x8008168a LBEG : 0x400853a9 LEND : 0x400853b1 LCOUNT : 0x00000027
Backtrace: 0x40085881:0x3ffc0f4c |<-CORRUPTED
I think the relevant line is this one:
E (815) gpio: gpio_set_level(226): GPIO output gpio_num error
I use the Heltec HTIT-WB32 device (with the ESP32-DOWDQ6 chip) and Platform.IO. As board, there is heltec_wireless_stick set. This should be the correct identifier (see here and here)?
Metadata
Metadata
Assignees
Labels
No labels