Enable compilation of spi-bcm2835.c from the mainline on a Raspbian Kernel #404
Conversation
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Signed-off-by: popcornmix <[email protected]>
Signed-off-by: popcornmix <[email protected]>
Signed-off-by: popcornmix <[email protected]>
Signed-off-by: popcornmix <[email protected]>
Signed-off-by: popcornmix <[email protected]>
Signed-off-by: popcornmix <[email protected]>
Signed-off-by: popcornmix <[email protected]>
Signed-off-by: popcornmix <[email protected]>
Experiments show that it doesn't really take that long to sync, so we can reduce the poll interval slightly. Might improve performance a bit.
The custom clock handling code is redundant and buggy. The MMC/SDHCI subsystem does a better job than it, so remove it for good.
Some additional quirks are needed for correct operation. There's no SDHCI capabilities register documented, and it always reads zero, so add SDHCI_QUIRK_MISSING_CAPS. Apparently SDHCI_QUIRK_NO_HISPD_BIT is needed for many cards to work correctly in high-speed mode, so add it as well.
Add a parameter to disable high-speed mode for the few cards that still might have problems. High-speed mode is enabled by default.
80 MHz clock isnt't suited well to be dividable to get SD clocks of 25 MHz (default mode) or 50 MHz (high speed mode). 50 MHz are perfect to drive the SD interface at ideal frequencies.
Commit d64b84c by accident reduced the maximum overall DMA sync timeout. The maximum overall timeout was reduced from 100ms to 30ms, which isn't enough for many cards. Increase it to 150ms, just to be extra safe. According to commit 872a8ff in the MMC subsystem, some cards require crazy long timeouts (3s), but as we're busy-waiting, and shouldn't delay for such a long time, let's hope 150ms will be enough for most cards.
…we can reliably recover from, so down_interruptable is not a safe call.
The additional FIFO might speed up transfers in some cases.
There are issues with both single block reads (missed completion) and writes (data loss in some cases!). Just don't do single block transfers anymore, and treat them like multiblock transfers. This adds a quirk for this and uses it.
…status=0 may improve interrupt latency
…ble_llm=0. Thanks ddv2005.
…. Should give about 10% more ARM performance. Thanks to Gordon and Costas
Failing to set up the FIQ correctly would result in "IRQ 32: nobody cared" errors in dmesg.
Fix several issues resulting in crashes or inconsistent state if a Model A root port was disconnected. - Clean up queue heads properly in kill_urbs_in_qh_list by removing the empty QHs from the schedule lists - Set the halt status properly to prevent IRQ handlers from using freed memory - Add fiq_split related cleanup for saved registers - Make microframe scheduling reclaim host channels if active during a disconnect - Abort URBs with -ESHUTDOWN status response, informing device drivers so they respond in a more correct fashion and don't try to resubmit URBs - Prevent IRQ handlers from attempting to handle channel interrupts if the associated URB was dequeued (and the driver state was cleared)
A dwc_otg_urb would get leaked if the HCD enqueue function failed for any reason. Free the URB at the appropriate points.
and enable CONFIG_JUMP_LABEL See: raspberrypi#348
Aaro Koskinen reports the following oops: Installing fiq handler from c001b110, length 0x164 Unable to handle kernel paging request at virtual address ffff1224 pgd = c0004000 [ffff1224] *pgd=00000000, *pte=11fff0cb, *ppte=11fff00a ... [<c0013154>] (set_fiq_handler+0x0/0x6c) from [<c0365d38>] (ams_delta_init_fiq+0xa8/0x160) r6:00000164 r5:c001b110 r4:00000000 r3:fefecb4c [<c0365c90>] (ams_delta_init_fiq+0x0/0x160) from [<c0365b14>] (ams_delta_init+0xd4/0x114) r6:00000000 r5:fffece10 r4:c037a9e0 [<c0365a40>] (ams_delta_init+0x0/0x114) from [<c03613b4>] (customize_machine+0x24/0x30) This is because the vectors page is now write-protected, and to change code in there we must write to its original alias. Make that change, and adjust the cache flushing such that the code will become visible to the instruction stream on VIVT CPUs. Reported-by: Aaro Koskinen <[email protected]> Tested-by: Aaro Koskinen <[email protected]> Signed-off-by: Russell King <[email protected]>
In the error paths of parse_open, only unlock the service if it is not NULL. In the fail path, NULL the service after it is unlocked to prevent a double unlock.
Commit 2ba85e7 (ARM: Fix FIQ code on VIVT CPUs) causes the following build warning: arch/arm/kernel/fiq.c:92:3: warning: passing argument 1 of 'cpu_cache.coherent_kern_range' makes integer from pointer without a cast [enabled by default] Cast it as '(unsigned long)base' to avoid the warning. Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Russell King <[email protected]>
Certain low-speed devices take a very long time to complete a data or status stage of a control transaction, producing NAK responses until they complete internal processing - the USB2.0 spec limit is up to 500mS. This causes the same type of interrupt storm as seen with USB-serial dongles prior to c8edb23. In certain circumstances, usually while booting, this interrupt storm could cause SD card timeouts.
Issuing low-speed packets when the root port is in full-speed mode causes the root port to stop responding. Explicitly fail when enqueuing URBs to a LS endpoint on a FS bus.
to get compiled also for a raspbian kernel. There are some advantages to this code - primarily that it uses the transfer one message interface. also the code is much cleaner. What is still missing: * the driver currently does not set the Alternate functions for the PINs, so one has to use spi-bcm2708 to set them up * there is no option to enable real time priorities to the work-queue * the CS-Polarity bug has not been fixed either... The last 2 are separate pull requests... Signed-off-by: Martin Sperl <[email protected]>
|
I don't use spi, so I'll need to get some input from other spi users. |
I assume this specific code in bcm2835_spi_init_pinmode comes from Chris Boot. This portion should get improved to avoid the hack that is there currently Signed-off-by: Martin Sperl <[email protected]>
|
yes - that is the idea - this way we do not have any compatibility issues. Also I will implement the fix for the ChipSelect Polarity bug only in this driver... Still I would recommend moving to the upstream SPI driver at some point, as it is upstream and the way forward... The alternate pin config is currently "hacked" in like it is in the spi-bcm2708.c driver. |
|
Note that there seems to be an issue with the "stock" spi-bcm2708 driver that results in a kernel-panic (and drop into kernel debugger) as soon as a SPI-message gets delivered via an spi_async directly from a interrupt-handler... The patched spi-bcm-2835.c driver does NOT show this effect! I hope I find time to rebase this patch soon, so that you can include it more easily... |
|
@msperl Can you close this please? |
skullandbones
pushed a commit
to skullandbones/linux
that referenced
this pull request
Jul 29, 2019
[ Upstream commit 28261da ] Because of both sides doing L2CAP disconnection at the same time, it was possible to receive L2CAP Disconnection Response with CID that was already freed. That caused problems if CID was already reused and L2CAP Connection Request with same CID was sent out. Before this patch kernel deleted channel context regardless of the state of the channel. Example where leftover Disconnection Response (frame raspberrypi#402) causes local device to delete L2CAP channel which was not yet connected. This in turn confuses remote device's stack because same CID is re-used without properly disconnecting. Btmon capture before patch: ** snip ** > ACL Data RX: Handle 43 flags 0x02 dlen 8 raspberrypi#394 [hci1] 10.748949 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 raspberrypi#395 [hci1] 10.749062 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 raspberrypi#396 [hci1] 10.749073 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 raspberrypi#397 [hci1] 10.752391 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 raspberrypi#398 [hci1] 10.753394 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 raspberrypi#399 [hci1] 10.756499 L2CAP: Disconnection Request (0x06) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 raspberrypi#400 [hci1] 10.756548 L2CAP: Disconnection Response (0x07) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 raspberrypi#401 [hci1] 10.757459 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 raspberrypi#402 [hci1] 10.759148 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 = bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447 > HCI Event: Number of Completed Packets (0x13) plen 5 raspberrypi#403 [hci1] 10.759386 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 raspberrypi#404 [hci1] 10.760397 L2CAP: Connection Request (0x02) ident 27 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 raspberrypi#405 [hci1] 10.760441 L2CAP: Connection Response (0x03) ident 27 len 8 Destination CID: 65 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 raspberrypi#406 [hci1] 10.760449 L2CAP: Configure Request (0x04) ident 19 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > HCI Event: Number of Completed Packets (0x13) plen 5 raspberrypi#407 [hci1] 10.761399 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 16 raspberrypi#408 [hci1] 10.762942 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Similar case after the patch: *snip* > ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143 L2CAP: Disconnection Request (0x06) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073 L2CAP: Connection Request (0x02) ident 12 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371 L2CAP: Disconnection Response (0x07) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196 L2CAP: Configure Request (0x04) ident 13 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804 L2CAP: Connection Response (0x03) ident 12 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Fix is to check that channel is in state BT_DISCONN before deleting the channel. This bug was found while fuzzing Bluez's OBEX implementation using Synopsys Defensics. Reported-by: Matti Kamunen <[email protected]> Reported-by: Ari Timonen <[email protected]> Signed-off-by: Matias Karhumaa <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
popcornmix
pushed a commit
that referenced
this pull request
Jul 31, 2019
[ Upstream commit 28261da ] Because of both sides doing L2CAP disconnection at the same time, it was possible to receive L2CAP Disconnection Response with CID that was already freed. That caused problems if CID was already reused and L2CAP Connection Request with same CID was sent out. Before this patch kernel deleted channel context regardless of the state of the channel. Example where leftover Disconnection Response (frame #402) causes local device to delete L2CAP channel which was not yet connected. This in turn confuses remote device's stack because same CID is re-used without properly disconnecting. Btmon capture before patch: ** snip ** > ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 #395 [hci1] 10.749062 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499 L2CAP: Disconnection Request (0x06) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548 L2CAP: Disconnection Response (0x07) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 = bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447 > HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397 L2CAP: Connection Request (0x02) ident 27 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 #405 [hci1] 10.760441 L2CAP: Connection Response (0x03) ident 27 len 8 Destination CID: 65 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449 L2CAP: Configure Request (0x04) ident 19 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Similar case after the patch: *snip* > ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143 L2CAP: Disconnection Request (0x06) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073 L2CAP: Connection Request (0x02) ident 12 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371 L2CAP: Disconnection Response (0x07) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196 L2CAP: Configure Request (0x04) ident 13 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804 L2CAP: Connection Response (0x03) ident 12 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Fix is to check that channel is in state BT_DISCONN before deleting the channel. This bug was found while fuzzing Bluez's OBEX implementation using Synopsys Defensics. Reported-by: Matti Kamunen <[email protected]> Reported-by: Ari Timonen <[email protected]> Signed-off-by: Matias Karhumaa <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
popcornmix
pushed a commit
that referenced
this pull request
Jul 31, 2019
[ Upstream commit 28261da ] Because of both sides doing L2CAP disconnection at the same time, it was possible to receive L2CAP Disconnection Response with CID that was already freed. That caused problems if CID was already reused and L2CAP Connection Request with same CID was sent out. Before this patch kernel deleted channel context regardless of the state of the channel. Example where leftover Disconnection Response (frame #402) causes local device to delete L2CAP channel which was not yet connected. This in turn confuses remote device's stack because same CID is re-used without properly disconnecting. Btmon capture before patch: ** snip ** > ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 #395 [hci1] 10.749062 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499 L2CAP: Disconnection Request (0x06) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548 L2CAP: Disconnection Response (0x07) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 = bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447 > HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397 L2CAP: Connection Request (0x02) ident 27 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 #405 [hci1] 10.760441 L2CAP: Connection Response (0x03) ident 27 len 8 Destination CID: 65 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449 L2CAP: Configure Request (0x04) ident 19 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Similar case after the patch: *snip* > ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143 L2CAP: Disconnection Request (0x06) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073 L2CAP: Connection Request (0x02) ident 12 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371 L2CAP: Disconnection Response (0x07) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196 L2CAP: Configure Request (0x04) ident 13 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804 L2CAP: Connection Response (0x03) ident 12 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Fix is to check that channel is in state BT_DISCONN before deleting the channel. This bug was found while fuzzing Bluez's OBEX implementation using Synopsys Defensics. Reported-by: Matti Kamunen <[email protected]> Reported-by: Ari Timonen <[email protected]> Signed-off-by: Matias Karhumaa <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
Patch to make it possible to compile the mainline spi-bcm2835.c spi driver on the raspbian kernel, which still does not use device-tree as well as the 2708 Architecture name.
There are some advantages to this code:
What is still missing:
The last 2 are separate pull requests, so that they can get merged into the mainline as well...
I would also recommend enabling this driver as a module in the default compiles.
Signed-off-by: Martin Sperl [email protected]